REMOVING XLOC CABLE FROM FORK INSTALL
REMOVING XLOC CABLE FROM FORK FULL
REMOVING XLOC CABLE FROM FORK ZIP

REMOVING XLOC CABLE FROM FORK ZIP

Measure the distance between the dust wiper and the o-ring or zip tie. Dismount your bike without bouncing, to avoid further moving the o-ring or zip tie.While in your riding position, slide the o-ring (or zip tie) down against the fork dust wiper.Make sure you distribute your weight evenly between the saddle, handlebars and pedals. Assume your riding position for at least 10 seconds, allowing the suspension to fully settle. Dressed to ride (including a filled hydration pack, if you use one), position your bike next to a wall or table to support yourself.If you have LSC or HSC/LSC adjust, make sure all adjusters are open (fully counter-clockwise.If you have a 3-Position Remote fork, set the fork to Open mode.Rotate the compression lever to the Open mode (fully counter-clockwise).Make sure that your compression adjusters are in the Open position.

REMOVING XLOC CABLE FROM FORK INSTALL

Using your forks sag setting o-ring on the left upper tube (or temporarily install a zip tie to the upper tube), slide the o-ring (or zip tie) down against the fork dust wiper.Pump your fork to the appropriate pressure as listed in the 'Suggested starting points for setting sag' table below, then remove the pump.Attach a FOX High Pressure Pump to the Schrader valve.Unscrew the air cap on top of the left fork leg counter-clockwise to expose the Schrader valve.Sag range should be set to 15–20% of total fork travel. Sag is the amount your suspension compresses under your weight and riding gear. To achieve the best performance from your FOX suspension, adjust the air pressure to attain your proper sag setting. Sag should be set to 15 - 20% of total fork travel Tighten the pinch bolt on the drive side dropout to 5.1 Nm (45 in-lb) torque. Compress the fork a couple of times to ensure that the lower leg has settled into its low-friction point.Ĥ. Use a 6 mm hex wrench to torque the KaboltX axle clockwise to the torque specification that is etched on the head of the Kabolt.ģ. Slide the KaboltX axle through the drive side dropout and hub.Ģ. Loosen the pinch bolt, then install the front wheel into the fork dropouts. NOTE: KaboltX is only compatible with the 2021 36 and 38 forks.ġ. Repeat the axle installation instructions to verify proper installation and adjustment.

REMOVING XLOC CABLE FROM FORK FULL

With the 4 mm adjuster set properly, you should start to feel tension in the axle when the QR lever is 90 degrees before full closure in the vertical position.Ĥ. While holding the QR lever open and stationary so it cannot rotate, use a 4 mm hex wrench in the center of the end of the axle to adjust the lever position. Note which direction the axle lever needs to turn to achieve proper orientation.ģ. If you are changing wheels or hubs, it is likely that the pinch bolt will need to be adjusted by following these installation instructions starting at step 1.ġ. After tightening the pinch bolt, you may remove the QR axle and replace it without loosening or retightening the pinch bolt.

IMPORTANT: You will only need to tighten the pinch bolt during your first wheel installation. Compress the fork a couple of times to ensure that the lower leg has settled into its low-friction point.Ĩ. If the lever does not have enough tension, or has too much tension when closed at the recommended position (1-20 mm in front of the fork), see the next section for adjustment instructions.ħ. The closed lever position must be between 1-20 mm in front of the fork leg.Ħ. The lever must have enough tension to leave an imprint on your hand.ĥ. Turn the axle clockwise 5-6 complete turns into the axle nut.Ĥ. Slide the axle through the drive side dropout and hub.ģ. Install Your Wheel Correctly to Benefit From the Floating Axleġ.

Removing xloc cable from fork